Liberte Environmental Associates

Effluent Concentrations from EPA's Development Document
Process Summary for Fish Meal with Solubles Plant
(i.e., with Evaporator)




Daily monitoring reports (DMR) are often inadequate for determining likely effluent wastewater characteristics because representative sampling may not be occurring. Omission of key pollutant parameters in specific discharge categories also leaves gaps in the effluent concentration data. An important solution to these problems is to source the original EPA development document to obtain reliable effluent concentration data to be used in mixing zone modeling and ambient water quality evaluation. These EPA development documents for effluent limitations guidelines are the basis of many pollutant limits in regulatory NPDES permits.

 

Process effluent summaries are contained, for example, in the Development Document for Effluent Limitations Guidelines and New Source Performance Standards for the Fish Meal, Salmon, Bottom Fish, Clam, Oyster, Sardine, Scallop, Herring, and Abalone Segment of the Canned and Preserved Fish and Seafood Processing Industry Point Source Category: Group 1, Phase II [EPA, September 1975]. Consider the fish meal with solubles plant (FMS) process summary for EPA selected parameters in Table 1(FMS). This table is derived from Table 20 of the Development Document (p. 78).

 

Table 1(FMS). Fish Meal with Solubles Plant (i.e., with Evaporator) Process Summary for EPA Selected Parameters


Parameter

 


Mean

Log Normal Mean

Log Normal STD DEV

99% Maximum

Production

ton/hr

33.4

NGA

28.2

NG

Time

hr/day

22.1

NG

2.22

NG

Flow

gpm

3,840

NG

2,470

NG

Flow Ratio

gal/ton

8,400

9.04

0.046

9,340

TSS

mg/l

26.2

3.27

0.397

66.1

BOD5

mg/l

84.4

4.44

0.194

133

Oil & Grease

mg/l

16.0

2.78

0.153

22.9

pH

S.U.

6.07

NG

1.40

NG

ANG-Not Given by EPA.

 

The mean value of 84.4 mg/l for biochemical oxygen demand (five-day, i.e., BOD5) for fish meal with solubles plant (i.e., with evaporator) is reported by the EPA as summarized in Table 1(FMS). For comparison, this value is 0.44 times the medium strength of untreated domestic wastewater of 190 mg/l [see reference 1]. Domestic wastewater, which includes untreated raw sewage, typically requires secondary treatment to reduce BOD5 to 45 mg/l on a weekly average basis, and 30 mg/l on a monthly average basis [2]. When high range BOD5 concentrations are considered, the 99 percent maximum value of 133 mg/l for FMS is 0.38 times the 350 mg/l value for high strength untreated domestic wastewater.

 

Values for total suspended solids (TSS), and oil and grease (O&G), are also considerably higher for FMS than for untreated domestic wastewater. The mean TSS value of 26.2 mg/l for FMS is 0.12 times the concentration of 210 mg/l for medium strength untreated domestic wastewater [1]. The 99% maximum TSS value of 66.1 mg/l for FMS is 0.165 times the concentration of 400 mg/l for high strength untreated domestic wastewater.

 

The mean O&G value of 16.0 mg/l for FMS is over 0.178 times the concentration of 90 mg/l for medium strength untreated domestic wastewater [1]. The 99% maximum O&G value of 22.9 mg/l for FMS is 0.229 times the concentration of 100 mg/l for high strength untreated domestic wastewater.

 

[1] Wastewater Engineering Treatment and Reuse, Metcalf & Eddy, 4th Edition revised by Tchobanglous, et al., McGraw-Hill, 2003, Table 3-15, pp. 186-187.

 

[2] Ibid., pp. 3-9.